Battery Service Equipment

%PM, %14 %026 %2019 %23:%Aug

Battery Tester – Tester T10 – Lemania Energy / Swiss

T10

Battery Tester – Tester T10 – Lemania Energy / Swiss

Tester T10

Battery Tester & Electrical System Analyzer
12V Car & Motorcycle batteries
Fully Graphical Interface
LCD Display
Integrated Printer
Touch Pad with Sensor technology
WET, AGM Flat, AGM Spiral, EFB, GEL, Ca
CCA, SAE, EN, IEC, DIN, CA/MCA, JIS, EN1, EN2
Starter Test
Alternator Test
Grounding Test
Data transfer to PC
Test Results Memory Saving

Description

Battery Test:

Analyses the battery condition using microprocessor-controlled testing methods without the need of fully charging it before test.

Consume very little current during testing, hence the test can be repeated numerous times without any worry on battery drainage and results are highly accurate.

Extremely safe as there is no sparks created during clamping and full analysed result takes less than 8 seconds to obtain.

Temperature compensation on end results.

Powered up by testing battery or any external DC source ranging from 9V to 15V. The analyser is meant to be operated on 12V flooded lead acid, sealed lead acid, and VRLA, EFB (Start/Stop) and AGM batteries. No maintenance is required during its lifetime service.

Grounding Test:

Analyses the condition of the electrical return circuit contacts resistance which were connected to the engine or chassis body from the battery terminal with results and recommendations display after test.

Starter Test:

Check the cranking effectiveness of the battery for indication on when the battery may fail to crank based on voltage profiles with results and recommendations display.

Alternator Tests (with diode ripple test):

These tests check the alternator charging conditions without load at 3,000 RPM, with load at 2,000 RPM and the diodes ripple volts with results and recommendations display after each test. This test determines whether the alternator is performing its job properly.

SPECIFICATIONS

Operating Voltage: 9V ~ 15V DC (max)
Analysing Capacity (Amps)
Automotive Batteries: CCA/SAE:100A ~ 2000A / EN: 100A ~ 2000A / CA/MCA:100A ~ 2000A / IEC: 100A ~ 2000A / DIN: 100A ~ 2000A / JIS#: 100A ~ 2000A
Motorcycle Batteries: CCA/SAE: 40A ~ 600A / EN: 40A ~ 600A / CA/MCA: 40A ~ 600A / IEC: 40A ~ 600A / DIN: 40A ~ 600A / JIS#: 40A ~ 600A
DC Volts Accuracy: ± 1%
Reading Battery Analysing Time: Less than 8 seconds.
Maximum key-in Characters: 17 Characters
Safety: Reverse polarity protected. Analyser will not power ON.
Internal Memory Storage: Store up to 70 Test Results.
PC Communication: Through USB Port.
Printer: Built-in
Printer Head: Thermo unit.
Paper Width: 57.5mm±0.5mm
Paper Roll Diameter: Max. 45mmO.D
Printing Speed: 50mm/sec
Working Temperature: 0ºC (32°F) ~ 50ºC (122ºF).
Working Humidity: 10 ~ 80 %

Published in Tester

%PM, %14 %023 %2019 %23:%Aug

Battery Tester – Tester T11 – Lemania Energy / Swiss

t11

Battery Tester – Tester T11 – Lemania Energy / Swiss

Description

Battery Tester & Electrical System Analyzer
12V/24V Car & Motorcycle batteries
Fully Graphical Interface
LCD Display
Integrated Printer
Touchpad with Sensor technology
WET, AGM Flat, AGM Spiral, EFB, GEL, Ca
CCA, SAE, EN, IEC, DIN, CA/MCA, JIS, EN1, EN2
Starter Test
Alternator Test
Grounding Test
Data transfer to PC
Test Results Memory Saving

Specifications

Operating Voltage: 9V ~ 15V DC (max)
Analysing Capacity (Amps):
Automotive Batteries:
CCA/SAE : 100A ~ 2000A
EN1/EN2: 100A ~ 2000A
CA/MCA : 100A ~ 2000A
IEC: 100A ~ 2000A
DIN : 100A ~ 2000A
JIS#: 100A ~ 2000A
Motorcycle Batteries:
CCA/SAE : 40A ~ 600A EN1/EN2:40A ~ 600A
CA/MCA : 40A ~ 600A IEC: 40A ~ 600A
DIN : 40A ~ 600A JIS#: 40A ~ 600A
DC Volts Accuracy: ± 1% Reading
Battery Analysing Time: Less than 8 seconds.
Max key-in Characters: 17 Characters
Safety: Reverse polarity protected. Analyser will not power ON.
Internal Memory Storage: Store up to 70 Test Results.
PC Communication: Through USB Port.
Printer: Built-in
Printer Head: Thermo unit.
Paper Width: 57.5mm0.5mm
Paper Roll Diameter: Max. 45mmO.D
Printing Speed: 50mm/sec
Working Temperature: 0ºC (32°F) ~ 50ºC (122ºF).
Working Humidity: 10 ~ 80 %

Published in Tester

%PM, %14 %021 %2019 %23:%Aug

Battery Charger – Smart Charger 12 / 24V – 25 A – Lemania Energy / Swiss

Smart

Battery Charger – Smart Charger 12 / 24V – 25 A – Lemania Energy / Swiss

Smart Charger 12 / 24V – 25 A

12V/24V Compatibility / Memory Function/ Fully Interactive MCU controlled program / Fast Charging Technology / Power Factor Correction / Complete Protection / All Types of Battery / Abnormally protection / Recovery Mode / Extendable Connectors / Cold/AGM Mode.

Description

Battery Voltage: 12V / 24V
Voltage selection: Automatic
Min-Max capacity of battery for charging: 50-450A(12v) / 25-230A(24v)
Max. battery capacity for maintenance: 500A
Charging current (Amp.): 12V 25A +/-10% – 24V 12,5A +/-10%
Battery types: WET, MF, GEL, AGM, Ca-Ca
Charging program: Constant current,constant voltage
Ambient temperature, output is reduced automatically at high temp: Reduced output power at higher temperature
IP Protection: IP44 (Fan version)

Published in Charger

%PM, %14 %985 %2019 %22:%Aug

Battery Charger - CHARGER FLASH 100 Amp. – Lemania Energy / Swiss

Falsh 100

Battery Charger - CHARGER FLASH 100 Amp. – Lemania Energy / Swiss

Description

Inverter energy efficient battery charger is a new kind of advanced pulse battery charger which comes with yellow-green backlit LCD display and can automatically detect, analyze, charge and maintain batteries, and intelligent programming.

Over-voltage and over-current protection, power down alarm, short circuit protection, reverse polarity protection, high temperature alarm and auto repair battery during charging process Detect, analyze, charge and maintain different types of batteries, applying to advanced charging devices at garages and repair workshops.

Used in the maintenance, detection and electronic control system programming process of cars in static state to prevent damage of control elements and loss of data caused by cars running out of battery during programming or other detection processes.

With reverse connection reminder and no touch spark, the charger is applicable to all battery technologies to perform charging curves and charging detection.

Specification:

Input voltage: AC200-240
V Input power: 1500W
Maximum Charging Current: 100A
Frequency: 50/60 Hz
Charging Voltage: 12V
Programming Mode:2~30V/2~100A
Battery Capacity: 10~1200A
Inverter

Published in Charger

%PM, %14 %972 %2019 %22:%Aug

Battery Charger – Battery Charger Combined Booster – Neo Start 420 – GYS / France

Gys 420

Battery Charger – Battery Charger Combined Booster – Neo Start 420 – GYS / France

The Neostart 420 maintains batteries even deeply discharged battery.
The Neos tart 420 charges 12V and 24V lead acid batteries from 20Ah to 1000Ah.
It is a traditional charger.

CHARGER FUNCTION

The Neostart 420 is protected against short circuits, polarity inversion and mains overvoltage.
On board storage for cables and clamps
Integrated wheels for portability
Cables Ø 10 mm², (length: red - 2m, black - 1.8m)
Externally visible and easily accessible fuse
Large ammeter